Wish to know how one can use a Router Table? Listed here are tricks to get probably the most out of your router table.
You don’t want a miter channel. Usually, you slide your work alongside the fence. If utilizing a miter channel, then the fence should be sq. to the miter channel. Why go to that bother?
You may create a jig to glide alongside the Fence. This mechanically aligns the wooden to get a sq. minimize. You can also make adjustment in profile and depth of minimize. A Router Carry makes this simple router bit set B09TR8Z82F TOOLDO.
A high quality Router Table fence eases dust assortment. Use your Router Table and Fence for simplicity and ease!
It is best to by no means put your work between the fence and the router bit. That’s simply asking for bother.
Usually, you slide the wooden from proper to left (when wanting on the fence from the entrance). That’s an anti-climb minimize. You make almost all cuts this fashion.
If very cautious, you possibly can go a short distance in the other way. However you should maintain on tight to keep away from kickback and/or injury. This climb minimize provides cleaner edges, however it’s best to solely try it after a variety of expertise.
Solely do lower than 15% of your work this fashion. It is best to solely use shallow or light cuts. Do NOT take large cuts. Solely do it if you arms are protected and away from the router bit.
How you can use a Router Table to heart edge-to-edge joints:
Have you ever ever questioned how one can heart edge-to-edge joints? You utilize this method for making strong tabletops, broad panels, and even make edging to go round your router table prime.
Let’s use an precise instance of oak edging on a MDF Router Table Prime. The highest is 1 1/8″ thick. The oak edging is 1 1/8″ thick.
How will we guarantee a centered edge?
- Determine on the tongue dimension. You have got a 1/4″ slot cutter. You need the tongue thickness lower than two occasions the minimize. Due to this fact, the tongue thickness is barely lower than 1/2″. We use a 1/4″ depth of minimize for this instance.
- We would like a tongue that’s lower than 1/2″ in thickness. Due to this fact, we all know that the rabbet on the Table Prime is barely greater than 5/16″ on either side of a 1 1/8″ thick piece.
- Rabbet the highest with a rabbet bit with a bearing to supply a 1/4″ rabbet. You do not need to take quite a bit throughout your first move. Due to this fact, the depth of minimize is ready for 1/8″ on your first move.
- Set the fence so it’s even with the bearing of the rabbet bit.
- Minimize each prime and backside of the highest. Take your time and go all the way in which round. Make certain the workpiece is flat on the Router Table Prime. Or use the router on prime of the workpiece.
- Measure the thickness of the tongue. Whether it is bigger than 1/2″, then regulate the depth of minimize. A router elevate makes this simple. Notice: you rout either side; subsequently use one-half the adjustment for all sides.
- Make your adjustment, rout the highest and backside once more. The tongue’s thickness is now barely lower than 1/2″.
- Exchange your rabbeting bit along with your 1/4″ slot cutter. I all the time disconnect the power supply to the router earlier than altering bits!
- Sit the rabbeted piece on the router tabletop close to the slot cutter. Increase the Router so the underside of the slot cutter aligns with the underside of the tongue. Chances are you’ll want help if the workpiece is giant.
- Set the depth of minimize for the slot to round 3/16″ initially. Now slot your Oak edging. Flip it over and slot once more. Take a look at the slot on the tongue. Is it too tight? If that’s the case, keep in mind that you make two passes with the slotter. Solely decrease your slot bit by 1/2 of the dimension wanted. By the way in which, the Porter Cable 7518 Router makes this a snap.
- For the reason that slot minimize is 1/4″, the second move isn’t utilizing your entire cutter. You get an precisely heart slot that matches on the tongue.
- As soon as the slot (groove) matches on the tongue, you’re able to set your remaining depth of the groove. The ultimate depth of minimize is barely greater than 1/4″ to permit for glue.
- Set your fence for this remaining depth. Bear in mind – make two passes with the slotter. This offers you a precise match.
You should utilize this technique for any edge-to-edge joinery, similar to tabletops, panels, giant drawer fronts, and any time you need to be part of two-pieces. You get good alignment and a rock-solid joint.
If you wish to see how this takes care of glue-up, please go to Router Table Prime
To make your personal router elevate, go to a simple to make Router Carry
For extra data on Utilizing Your Router Table, together with photos and suggestions, please go to How you can Use a Router Table